Insert molding ye mun ye?
Insert Molding ye pikiri kɛcogo ye min bɛ baara kɛ ni fɛn dɔ ye min bɛ kɛ ka fɛn dɔ don a la plastiki yɔrɔ la. O kɛcogo bɛ kɛ ni fɛɛrɛ fila ye minnu ka kan ka kɛ. A fɔlɔ, yɔrɔ dafalen dɔ bɛ don bɔgɔdaga kɔnɔ sanni a dilanni kɛcogo ka kɛ tiɲɛ na.
Mun de ye kojugu ye?
E Kɔrɔya tɛmɛnen ye fɛn dilanni taabolo ye min bɛ kɛ ni fɛn caman faralen ye ɲɔgɔn kan cogo la min tɛ fɛn ye ka kɛ yɔrɔ kelen walima fɛn kelen ye. Fɛn fila de bɛ yen minnu ka kan ka kɛ walasa ka tɛmɛ o kan.
Fɛn fɔlɔ min bɛ kɛ, o ye ka substrat dɔ mɔ ani ka a furakɛ min ka teli ka kɛ plastiki ye.Danfara minnu bɛ sɔrɔ overmolding vs insert molding ni ɲɔgɔn cɛ
hali ni ɲɔgɔn caman bɛ don insert mouding ni overmulding cɛ ka da u kɛcogo kan, danfara dɔw bɛ yen. Overmolding vs. insert molding difference spans over the nin:
Waleyali
Fɛn minnu bɛ don a kɔnɔ, olu ye fɛnw ye minnu bɛ kɛ ka plastiki yɔrɔw siri ani ka u lajɛ ɲɔgɔn fɛ. Tuma dɔw la, hali fɛn fila bɛ kɛ yɔrɔ kelen na walasa ka baara kɛ ka ɲɛ. Nin yɔrɔ in na, fɛn minnu bɛ kɛ ka caya, olu lisɛli bɛ duguma.
Cɛw ka jiriw
Musow ka jiriw
kuran kontasiyɔnw
resɔrɔn-doniw
dowel pinw
ka teli ka kɛ ni lastikuw ye minnu bɛ kɛ ni fɛn ye min bɛ fara ɲɔgɔn kan plastiki yɔrɔ dɔ sanfɛ. Substrat min bɛ baara kɛ ni TPE walima TPU ye a ka c’a la.
Ka tɛmɛ
O damatɛmɛko bɛ tali kɛ fɛn dilanni taabolo fila la. Substrat (sɔgɔlan) mouling (sɔgɔli) ni a kɛnɛyali bɛ na ni sen kelen ye, k’a sɔrɔ sen filanan ye ka layɛrɛ wɛrɛ mɔ fɔlɔ kan. Insert insert injection moulding tɛ kɛ ni sen fila dilanni ye. O bɛɛ n’a ta, a laban na, a bɛ na ni layini wɛrɛ dilanni ye fɛn dɔ sanfɛ.
Teliya
Insert molding bɛ waati ta ka layɛrɛ wɛrɛ mɔ fura kan bawo o yɔrɔ fila bɛɛ bɛ dilan u dan na. O b’a to a bɛ waati ta ka tɛmɛ a dan kan. A bɛ na ni fɛn bɛɛ lajɛlen ye min bɛ kɛ fɛn dilannen kɔnɔ, a tɛ i n’a fɔ overmolding, o min bɛ kɛ ni encapsulation yɔrɔ dɔ ye.
O damatɛmɛko bɛ dɔ bɔ a dilanni waati la. O bɛ se ka kɛ bawo a tɛ o yɔrɔ fila bɔ u danma wa a bɛ fɛn filanan dilanni tilennen wajibiya ka ɲɛsin fɛn dilannen ma. Nka, ka tɛmɛ a dan kan, o ka gɛlɛn; O la, baarakɛlaw ka kan ka tugu cikanw kɔ minnu fɔra.
Material Selection .
Nɔgɔw tɛ mako ɲɛ ka tɛmɛ u dan kan. O la, fɛn dilannenw ka teli ka to sen na kosɛbɛ ani ka se ka fɛn caman kɛ. Mako tɛ masin sirilan suguya si la insert mouling kɛcogo la bawo nɛgɛ yɔrɔ nafamaw bɛ sɔrɔ nɔgɔ la. K’a sababu kɛ fɛnw ye minnu bɛ kɛ, fɛn minnu bɛ tɛmɛ ka tɛmɛ u dan kan, olu ka teli ka barika sɔrɔ ka tɛmɛ fɛnw kan minnu bɛ tɛmɛ dondaw la.
Sɔngɔ
Insert insert insert moulding bɛ dɔ bɔ kosɛbɛ assemblage musaka la ani ka a sɔrɔ a yɔrɔ ba kelen ni kɔ bɛ se ka kɛ. Insert Insert Injection Moulding musakaw bɛ dɔgɔya kosɛbɛ ni a dilanni hakɛ ka ca. Nka, ka tɛmɛ a dan kan, o bɛ kɛ ni fɛɛrɛ fila ye, wa a sɔngɔ ka bon ka tɛmɛ fɛn donta kan.
